Open 7 days a week · 7am – 9pm Serving Independence, MO & 20 surrounding towns

Chimney Liner Installation in Independence, MO

A chimney liner carries smoke and gases out and keeps heat away from the house. Jake And Son Chimney Sweep installs and replaces chimney liners in Independence, MO and 20 nearby towns.

A chimney needs relining when its liner is cracked, missing, or the wrong size for the appliance connected to it. A stainless steel liner, sized to the fireplace insert, stove or furnace, is the usual fix. Chimney liner installation from Jake And Son Chimney Sweep starts at $1,199 and follows NFPA 211.

When a chimney needs a new liner

A chimney needs a new liner in four situations: the existing liner is damaged, there has been a chimney fire, there is no liner at all, or a new appliance needs a different flue size.

How a stainless steel liner is installed

A stainless steel liner is lowered down the existing flue from the top, connected to the appliance at the bottom, and sealed with a top plate and cap.

  1. Inspect and measure. A camera inspection shows the condition and the route of the flue, and the liner is sized to the appliance.
  2. Prepare the flue. The flue is swept, and damaged tiles are removed where they would block the liner.
  3. Install the liner. The liner, with insulation where required, is lowered into place.
  4. Connect and seal. It is connected to the appliance, and a top plate and cap seal the chimney.
  5. Test the draft. The system is checked before it is used.

Think your chimney needs relining?

Call (816) 239-8989

Which liner is right

For most relining jobs the answer is stainless steel, because it can be sized exactly to the appliance. The alloy has to suit the fuel: liners for wood are different from liners for high-efficiency gas appliances. Our chimney liner comparison sets out clay tile, stainless steel and cast-in-place side by side.

What a chimney liner costs

Chimney liner installation starts at $1,199 for a short, straight flue. Flue height, diameter, insulation and bends in the flue add to that. See the pricing page for all starting prices. You get the price for your chimney after the inspection and before any work starts.

Why a fireplace can fail to heat the room

A chimney that draws smoke away cleanly can still leave the room cold. Three of the most common reasons are built into the fireplace and the flue, and relining is part of the fix for two of them.

An open masonry fireplace sends most of its heat up the flue

A traditional open masonry fireplace is a poor room heater by design. The fire radiates a little warmth into the room, but the great majority of the heat rides the hot gases straight up the chimney. On a cold Independence night, an open firebox can even run at a net loss, because the fast updraft pulls already-heated household air up the flue faster than the fire returns heat. The standard answer is to close the opening with an insert or a sealed glass door and connect it to a correctly sized liner, so the fire heats the room instead of the sky.

A flue that is the wrong size or too short

Flue size has to match the fire. A rough rule for an open fireplace is a flue cross-section about one-tenth of the fireplace opening; a flue much larger than that cools the smoke, slows the draft and leaves the fire sluggish and cool. Height matters just as much: a flue that stops too low, or ends below a nearby roofline, never builds a strong enough pull. We size and top the flue to the standard we work to, NFPA 211, and relining to the right diameter is often what turns a lazy, smoky fire into a hot one.

Poor insulation around the liner

An exterior masonry chimney on the cold side of the house pulls heat out of the flue gases before they can establish a draft. The gases cool, slow down and condense, the chimney itself acts like a cold sink, and the fire struggles to get going. Wrapping a stainless steel liner in an insulation blanket keeps the gases hot, so the draft starts faster and stays strong, more of the fire’s energy stays in the living space, and creosote has less chance to form.

When a failed liner is a hidden fire emergency

The liner is the barrier that keeps flue heat and gases off the masonry and the wood framing packed around your chimney. When it cracks, opens gaps, or loses a section, that barrier is gone, and a hot fire can drive heat and flame into the structure or let carbon monoxide seep into the home. There is often no obvious sign until a chimney fire or a camera inspection turns it up, which is why a roaring fire in the flue, a strong smoky smell, or pieces of tile in the firebox should stop you from burning. See our emergency chimney service page for what to do next.

Related services

Relining usually follows a Level 2 chimney inspection and is one of the repairs covered on our chimney repair page.

By Jake Baldwin, owner and founder (32 years in the trade), and Sam Baldwin, team leader and technician.
Last updated:

Common questions

How long does it take to install a chimney liner?

Most stainless steel liner installations are completed in a day. A tall chimney, a flue with bends, or damaged clay tiles that have to be removed first can extend the job. The fireplace or appliance can normally be used again as soon as the installation has been tested.

Do I need an insulated chimney liner?

For wood-burning stoves and inserts, insulation is usually required by the liner's listing and it is worth having. An insulated liner keeps the flue gases warm, which improves draft and reduces creosote. On an exterior chimney it also reduces condensation in gas appliance flues.

Can a chimney liner be installed in a chimney with bends?

Yes. Flexible stainless steel liner is made for flues with offsets and can follow most bends. A camera inspection beforehand shows where the bends are and whether any tiles need to be removed for the liner to pass. Sharp offsets can limit the liner diameter that will fit.

What size chimney liner do I need?

The liner is sized to the appliance, following the manufacturer's instructions and NFPA 211. A wood stove or insert normally takes a liner the same diameter as its flue outlet. Gas furnaces and water heaters are sized from their input rating and the height of the chimney.

Does a new chimney liner need maintenance?

Yes. A lined flue still needs the yearly inspection NFPA 211 calls for, and sweeping when deposits build up. A stainless liner is easier to sweep than old clay tile because it is smooth and round, and keeping it clean is what makes it last.

Ready to book? Talk to Jake or Sam.

Open 7am – 9pm, seven days a week.

(816) 239-8989
Tap to call (816) 239-8989